In this Tutorial, I want to share a technique to spruce up ordinary Jewelry Chain using the same materials used in the previous segments of this month’s project.
In Part 2, we used theSimple Loop and Wire Wrapped LoopTechniques, to complete the Earring and Pendant Components and add the gorgeous Drop Beads and Crystals.
We made perfectly matching Ear Wires to go with our project in Part 3.
Count down to the 6th link and cust with flush cutters. Repeat for the second section.
For the remaining sections, cut two at the 8th and 10th links.
Double check each set of chains to make sure they are equal.
I use a needle or any pointed object to lift the sections to get an accurate look.
If your chain is very small and hard to count follow these steps.
Measure and cut the first section.
Use a pointed object to pick up the two pieces of chain and measure prior to cutting.
Always cut at least one link longer than you think you need to make sure you aren’t going to make a mistake.
I can not tell you how many times I thought I was on the mark and wound up cutting the section too short.
If you make a mistake, don’t throw the sections away. You can always find a creative way to use these pieces in other projects.
The Beaded Links
Remember to start with a flush cut on the wire at the beginning of each link.
It is very important to mark your pliers to get the same size loops on both ends of your Beaded Links.
Make sure to place the wire in the same spot each time and your links will look perfect and professional.
I marked my pliers in the spot that creates a loop similar in size to the size of my chain links.
Thread on one of your Beads.
Hold the Bead and Loop firmly in place and measure up 3/8 inch above the Bead.
With the Flush side of the cutters facing the bead, cut the wire at the mark.
Grasp the end of the wire with the Round Nose Pliers, making sure you are on your mark and flush with the barrels.
The new loop should be formed on the same plane as the first loop but rolled in the opposite direction.
Make the Simple Loop on this end of the wire and gently center it over the bead.
Repeat all these steps for each of your remaining Beads.
Beaded Links can be a little tricky to master, so check out the Postand PDFif you need help mastering this skill and other options for making Beautiful Beaded Links.
Making the Connections
The first step is to layout your design components and decide how you want to proceed.
I have my chain section running from shortest to longest with the Pendant as my starting point.
I like the larger Beaded Links closest to the Pendant and the smaller ones going towards the back of the Necklace.
You have the option of using jump rings at each connection points, but I chose only to use them on the ends.
Open the first 6 mm Beaded link by pushing the loop over to the side using your Chain Nose Pliers.
Attach one end of your 5 link chain sections to the open loop.
Using the pliers again, push the loop back to center and make sure to close it completely.
Using both sets of your Chain Nose Pliers add one of the 3 mm Jump rings to the other end of your shortest Chain Sections.
Using the 2 sets of pliers, create Friction by rubbing the two sides of the Jump ring against each other until the ring snaps into closed position.
Use the Proper Technique to add the 7 link Chain to the opposite side of your Beaded Link.
Add the other 6 mm Link to the other end.
Add the 9 link Section of Chain next.
Add a 4 mm Link and then connect an 11 Link Chain Section to the other side.
Add a 4 mm Link to the other end.
Repeat all these Steps for the second side of the necklace.
Adding the Pendant
For this step, utilize the small jump rings on the end of your chains to make the connection.
Close the jump ring using the friction technique to insure it is closed properly.
Adjusting for Length
Divide your remaining Chain equally and add to the last Beaded Link on each side of your necklace.
Here you have the option to use longer sections of chain to add length to your piece.
You can add more beaded links too if you prefer.
It is up to you.
The Clasps
Use the last tow 5 mm Jump Rings to add the Soldered Rings and the Lobster Claw to the ends of your Chain.
Note the positioning of the Lobster Claw above. Proper positioning makes it easier to open and close the Clasp for you or your customers.
That’s a wrap for the lovely and elegant Pearls on the Halfshell Project.
I hope you fell in love with this beautiful mix of Bead Weaving with Wire Working Techniques.
Make sure to follow me here and on my Social Media for more great projects, videos and articles from The Alluring Bead Boutique.